Issue 5 / 2026

Inner covers

Article: Best recommended method for washing to disinfect and deodorise waste turkey feathers intended for insulation purposes

Author: EROL MÜSLÜM
Pages: 671–685
DOI: 10.35530/IT.077.05.202612
Published online: October 2026

Abstract

Waste turkey feathers (TF) must be washed to be used in the production of composite or nonwoven surfaces. Despite cleaning, these fibres can develop strong odours, especially as temperature increases. The gas chromatography-mass spectrometry (GC-MS) method was used to determine the oils and fatty acids that cause odour in clean or dirty TF structure and to see their changes depending on temperature. Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) images were used to determine whether there was any change in the chemical structure of the feathers after washing. The washing program results were compared, and the W6S program was identified as the most effective method for eliminating volatile substances that may cause odour. According to GC-MS results, the total area of the peaks covered by fatty acids and other substances in the chromatogram decreased by 593 times at 24°C and by 1250 times at 85°C compared to the W1 washing program. This situation provided saponification under the effect of sodium hypochlorite, which is a very strong base. Then, washing with nonionic soap, rinsing with sodium hydroxide and centrifuging were carried out to obtain odourless TF.
Keywords: turkey feather, disinfection of turkey feathers, bad odours, fibre washing method, gas chromatography-mass spectrometry

Citation: Müslüm, E., Best recommended method for washing to disinfect and deodorise waste turkey feathers intended for insulation purposes, In: Industria Textila, 2026, 77, 5, 671–685,   https://doi.org/10.35530/IT.077.05.202612

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: A generalizable high-fidelity fabric simulation system optimised for e-commerce and design workflows

Authors: YONG JI, JING SHI, MINGHUI QIU, JIA WEI, JINBAO ZHANG, HUA ZHANG
Pages 686–691 
DOI: 10.35530/IT.077.05.2025121
Published online: October 2026

Abstract

Achieving high-fidelity, real-time garment simulation is a central challenge in virtual try-on systems. This difficulty stems from the need to balance accurate fabric-body interaction with strict computational constraints. This study presents a data-driven fabric simulation framework that integrates deformation learning with geometric refinement to enable precise fitting and photorealistic detail at interactive speeds. Compared with conventional physics-based solvers and simplified learning pipelines, the proposed approach achieves improved wrinkle fidelity, more stable fabric body correspondence, and higher computational efficiency without sacrificing visual quality. These results demonstrate the framework’s practical viability for large-scale deployment in virtual try-on platforms, intelligent apparel design workflows, and digital retail visualisation applications. By unifying data-driven deformation learning with principled refinement strategies under a scalable computational paradigm, this work advances high-fidelity fabric simulation and provides a technical foundation for next-generation digital fitting, e-commerce platforms, and design workflows.
Keywords: fabric simulation, learning model, virtual reality, wrinkle preservation, dataset

Citation: Ji, Y., Shi, J., Qiu, M., Wei, J., Zhang, J., Zhang, H., A generalizable high-fidelity fabric simulation system optimized for e-commerce and design workflows, In: Industria Textila, 2026, 77, 5, 686–691,   https://doi.org/10.35530/IT.077.05.2025121

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: How does corporate financialization affect operational risk in textile firms? Evidence from China

Authors: XUHUA CHEN, YONGJIAN HUANG, CHUNHUA JU, XUSHENG FANG
Pages 692–705 
DOI: 10.35530/IT.077.05.2025130
Published online: October 2026

Abstract

Against the backdrop of a widening divergence between the virtual and real economies, coupled with the increasingly pronounced trend of financialization among traditional manufacturing enterprises, China’s textile industry, a vital pillar of the national economy and a core export-oriented sector, has witnessed a significant shift in resources toward financial activities. This trend may reshape the landscape of its operational risks. This study examines the impact of financialization on operational risk in China’s textile industry using listed firms from 2007 to 2024 as the sample. We find a significant positive correlation between corporate financialization and operational risk, which becomes more pronounced when the level of managerial myopia is higher. A series of robustness tests, such as using instrumental variables and propensity score matching, consistently support the baseline findings. Further analysis indicates that financialization affects operational risk through two channels: crowding out physical capital investment and increasing corporate opacity. Finally, we find that internal control quality and media coverage help mitigate the positive impact of financialization on operational risk. This study enriches the existing literature on the risk drivers and operational mechanisms in traditional manufacturing. It provides empirical support for textile enterprises to balance financial activities with core business development, and for regulatory bodies to optimise corporate governance and industrial policies.
Keywords: textile industry firms, corporate financialization, operational risk, managerial myopia, corporate governance

Citation: Chen, X., Huang, Y., Ju, C., Fang, X., How does corporate financialization affect operational risk in textile firms? Evidence from China, In: Industria Textila, 2026, 77, 5, 692–705,   https://doi.org/10.35530/IT.077.05.2025130


Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Novel zinc carbonate synthesis using olive wood ash extract: a sustainable approach for enhancing cotton flame retardancy

Authors: NEDRA ABBES, KHADIJA KHADDAJI, NEJIB SEJRI, BOUBAKER JAOUACHI, HONGLUAN LIU, JUN XU, IMENE BEKRI
Pages 706–714 
DOI: 10.35530/IT.077.05.2025129
Published online: October 2026

Abstract

This study presents a novel, sustainable, and cost-effective method for synthesising zinc carbonate (ZnCO3) via the precipitation of zinc acetate using an alkaline extract derived from olive wood charcoal ash, which stabilises at approximately pH 13.0. The formation of the desired (ZnCO3) flame retardant was confirmed using XRD and Fourier-transform infrared (FTIR) spectroscopy.
The synthesised (ZnCO3) was applied to cotton fabric via a pad-dry-cure process at two concentrations (0.5 wt. % and 1.4 wt. %), resulting in final add-on percentages of 6.0% ± 0.3% and 8.0% ± 0.4%. Flammability tests demonstrated significant fire resistance improvement: the burning rate of the fabric was reduced by up to 63%, decreasing from 0.62 cm/s (untreated) to 0.23 cm/s for the 8.0% treated sample, increasing total burning time from 48 s to 126 s. Mechanical characterisation revealed that the 8.0% treated fabric exhibited an enhanced tensile strength, increasing by an average of over 22% without significant fabric shrinkage. These findings highlight olive charcoal ash as a promising, sustainable, zero-cost alkali source and (ZnCO3) as an effective, eco-friendly flame-retardant coating for reinforced cotton textiles.
Keywords: zinc carbonate, sustainable synthesis, ash water, flame-retardant cotton

Citation: Abbes, N., Haddaji, K., Sejri, N., Jaouachi, B., Liu, H., Xu, J., Bekri, I., Novel zinc carbonate synthesis using olive wood ash extract: a sustainable approach for enhancing cotton flame retardancy, In: Industria Textila, 2026, 77, 5, 706–714,   https://doi.org/10.35530/IT.077.05.2025129

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Research on the collar-placket shape of modern vests and the inheritance of digital fashion matching

Authors: JUAN CHAI, RONG FU, PEIYI REN, ZHICHENG WANG, XIANGFANG REN, KAIXUAN LIU
Pages 715–728 
DOI: 10.35530/IT.077.05.2025162
Published online: October 2026

Abstract

The vest is a traditional clothing item in China that has been continuously used to the present day. It is highly practical, diverse in form, lightweight, flexible, and suitable for a wide range of occasions. Based on 81 physical objects and 76 historical image materials of modern vests collected by the Jiangnan University Folk Costume Museum as research samples, the study compares the evolution of vests, collar-placket shapes, and the evolution of wearing and matching through a triple-evidence methodology: physical surveying, historical imagery, and archival documentation. The study reveals that during the late Qing Dynasty and early Republic of China periods, popular stand-up collar styles of modern vests included single-breasted placket, pipa placket, front-opening placket, pair placket, and herringbone placket. The traditional continuation of the round-collar placket includes the single-breasted placket, pipa placket, front-opening placket, wavy single-breasted placket, pair placket, eight-character front placket, shoulder-opening placket, and no front placket. Additionally, special collar forms that reflect a blend of Chinese and Western styles include a square-collar frontopening placket, a boat-shaped collar with a shoulder-opening placket, a heart-shaped open collar with a slanting front, and a pullover collar. The research clarifies that vest wearing and matching evolved from the late Qing Dynasty combinations, such as vests worn with Manchu-style clothing, traditional long gowns and skirts, and traditional Chinese jackets and trousers, to the Republic of China era, where vests were commonly paired with cheongsams and inverted big sleeve suits. The AHP fuzzy comprehensive evaluation method has proven effective in assessing the digital display of modern vest-wearing forms, offering new insights into the preservation and inheritance of modern vest culture.
Keywords: modern vest, vest evolution, collar-placket shape, digital wearing matching, fuzzy comprehensive evaluation method

Citation: Chai, J., Fu, R., Ren, P., Wang, Z., Ren, X., Liu, K., Research on the collar-placket shape of modern vests and the inheritance of digital fashion matching, In: Industria Textila, 2026, 77, 5, 715–728,   https://doi.org/10.35530/IT.077.05.2025162

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Financial digitalisation driving 3D printing utilisation and enhancing operational performance in the Indian textile industry

Authors: RAMASAMI VIJAYAKRISHNAN, SEETHARAMPALAYAM CHETTIANNAN VETRIVEL, SJ JOE ARUN C, AROKIASAMY SELVANAYAGAM
Pages 729–739 
DOI: 10.35530/IT.077.05.202552
Published online: October 2026

Abstract

India’s textile sector is undergoing a significant shift as digital banking systems begin to reshape the way firms access capital, manage payments, and coordinate operations. As manufacturers increasingly use 3D printing for customised production and rapid prototyping, seamless digital financial services are now essential to sustaining efficient, well-coordinated supply chain operations. This study shows that rather than being merely auxiliary tools, advancements in digital banking actively accelerate the adoption of 3D printing technologies and improve operational responsiveness in textile companies. Despite these advancements, industry-wide growth still faces challenges like disjointed digital payment infrastructures, low user familiarity with banking technologies and credit disbursement delays. In order to overcome these limitations, the study presents an integrated Digital Banking–Enabled 3D Printing Supply Chain Model that shows how digital finance improves information flow, fortifies vendor relationships, streamlines procurement processes and facilitates design-to-production cycles. Empirical insights from a diverse group of 580 customers, 90 credit employees, and 35 digital banking administrators enabled a thorough assessment of mobility-based banking behaviour, loan dependence, transaction intensity, supply chain agility, and the degree of 3D printing utilisation. Partial least squares path modelling (PLS-PM) was used to examine seven theoretical pathways that relate digital banking capabilities to technological adoption, production adaptability, financial stability, and overall supply chain outcomes. The results are meant to assist financial institutions, regulators and leaders in the textile sector in developing a technologically advanced and creative manufacturing environment.
Keywords: 3D printing, digital banking, FinTech ecosystem, textile supply chain, PLS-SEM, digital credit access

Citation: Vijayakrishnan, R., Vetrivel, S.C., Arun, S.J.C., Selvanayagam, A., Financial digitalisation driving 3D printing utilisation and enhancing operational performance in the Indian textile industry, In: Industria Textila, 2026, 77, 5, 729–739,   https://doi.org/10.35530/IT.077.05.202552

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Integrating artificial intelligence into digital marketing strategies for the textile industry: enhancing customer engagement and sustainability

Authors: NALBANT KEMAL GOKHAN, AYDIN SEVGI
Pages 740–749 
DOI: 10.35530/IT.077.05.2025142
Published online: October 2026

Abstract

The textile industry is experiencing a rapid paradigm shift with the growing application of artificial intelligence in the processing, marketing, and consumption trends related to the textile industry. The objective of this research is to analyse the way the integration of artificial intelligence in digital marketing can result in enhanced customer engagement and sustainable practices. The worldwide market for artificial intelligence related to textiles is predicted to grow exponentially by 2033, portraying the increasing digitisation of the textile industry. There is a conceptual gap highlighted between artificial intelligence marketing trends and sustainable trends related to textiles. A model of balance between the textile industries for responsible use of artificial intelligence has therefore been incorporated within this research related to the textile industries as Balanced AI Adoption Framework (BAAF). A conceptual framework analysis was employed to review literature regarding the opportunities, challenges, and ethical risks of AI adoption in the textile industry. It was discovered through the results of this study that, through the gradual increase in the use of AI alongside human efforts, better outcomes may be achieved regarding industry efficiency and market responsiveness, with preserved creativity, transparency, and ethical viability.
Keywords: artificial intelligence, digital marketing, textile industry, customer engagement, sustainability, Industry 4.0

Citation: Gokhan, N.K., Sevgi, Y., Integrating artificial intelligence into digital marketing strategies for the textile industry: enhancing customer engagement and sustainability, In: Industria Textila, 2026, 77, 5, 740–749,   https://doi.org/10.35530/IT.077.05.2025142

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Comparison of the physical properties of cut-and-seal ultrasonic welding vs cut-and-sew overedge stitch

Authors: SERKAN BOZ, MEHMET KÜÇÜK
Pages 750–757 
DOI: 10.35530/IT.077.05.2025155
Published online: October 2026

Abstract

The usage area of ultrasonic welding, which is one of the trending methods of today, continues to increase daily. Ultrasonic welding is one of the methods used to transform textile surfaces into the final product. Thanks to the modifications made to this method, it is also possible to obtain joining systems similar to conventional methods. The joint obtained by cut-and-seal ultrasonic welding is identical to the cut-and-sew overedge stitch method, one of the traditional methods. For this reason, this study compared physical properties, including air permeability, water impermeability, seam strength, and thickness, of untreated and tape-coated joints produced by the two methods. Four functional fabrics commonly used in outerwear and outdoor products were examined. The results show that ultrasonic welding combined with tape significantly improves seam strength (up to 3–4 times higher compared to ultrasonic welding alone) while maintaining adequate air permeability and water impermeability. These findings suggest that ultrasonic welding can be considered a viable alternative to overedge stitching for high-performance applications.
Keywords: cut & seal ultrasonic welding, overedge stitch, comparison, joining methods

Citation: Boz, S., Küçük, M., Comparison of the physical properties of cut-and-seal ultrasonic welding vs cut-and-sew overedge stitch, In: Industria Textila, 2026, 77, 5, 750–757,   https://doi.org/10.35530/IT.077.05.2025155

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Influence of 3D-printed circular patterns on the tensile properties of tulle fabric

Authors: IULIANA STREBA, ARINA SEUL, AURA MIHAI, ANTONELA CURTEZA, MARIANA COSTEA, RAMONA BUDEANU
Pages 758–776 
DOI: 10.35530/IT.077.05.20266
Published online: October 2026

Abstract

This study investigates the influence of 3D printing on the tensile mechanical behaviour of tulle, a thin, mesh-like textile commonly used in clothing and technical applications. Four 3D printing geometries were analysed: small and large circles, arranged either aligned or staggered, applied to the surface of the tulle through fused deposition modelling (FDM). Tensile tests were conducted according to ISO 1421:2016, with adaptations required by the textile-polymer composite structure. Maximum force, elongation at break, specific strength, and Young’s modulus were evaluated and compared to unprinted control samples. The results show that all printed geometries significantly increase tensile strength compared to plain tulle. At the same time, elongation at break decreased, and the material stiffened with increasing print size and density. The paper highlights the potential of 3D printing to customise and optimise the mechanical properties of thin textiles, opening new directions in the design of flexible hybrid materials.
Keywords: 3D printing on tulle fabric, tensile properties, additive manufacturing, fused deposition modelling (FDM), PLA printed patterns

Citation: Streba, I., Seul, A., Mihai, A., Curteza, A., Costea, M., Budeanu, R., Influence of 3D-printed circular patterns on the tensile properties of tulle fabric, In: Industria Textila, 2026, 77, 5, 758–776,   https://doi.org/10.35530/IT.077.05.20266

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Using a 3D virtual clothing system to develop bottom patterns for South Korean women in their 40s

Authors: EOM RANI, PARK A-MI
Pages 777–784 
DOI: 10.35530/IT.077.05.2025124
Published online: October 2026

Abstract

This study aimed to analyse the lower body characteristics of South Korean women in their 40s and propose bottom patterns, such as for skirts or pants, using a 3D virtual clothing system. The lower body characteristics of South Korean women in their 40s were identified by comparing them with those of women in their 20s using the Mollison relational deviation line. The CLO software was employed to examine the bottom fits of South Korean women in their 20s and 40s and to analyse pressure points and clothing pressure. The pattern-drafting method was also suggested for South Korean women in their 40s. South Korean women in their 40s had lower height-related body measurements and larger circumference-related body measurements than South Korean women in their 20s. Therefore, the traditional drafting method of using clothing patterns for skirts and pants, such as using only the body measurements of women in their 40s, leads to inadequate fit. When designing bottom patterns for this demographic, the waist, abdomen, hip area, and hip length must be considered. For pants patterns, the crotch, thigh area, and pants silhouette should also be considered. This study is meaningful in that it analysed virtual clothing fit when designing bottom patterns for South Korean women in their 40s.
Keywords: middle-aged South Korean women, body characteristics, clothing fit, 3D virtual clothing system, pattern making

Citation: Rani, E., A-Mi, P., Using a 3D virtual clothing system to develop bottom patterns for South Korean women in their 40s, In: Industria Textila, 2026, 77, 5, 777–784,   https://doi.org/10.35530/IT.077.05.2025124

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: The impact of equity structure on technological innovation efficiency in China’s listed textile firms

Authors: GUANG CHEN, HUIKANG CHEN, SHOUCHAO HE
Pages 785–796 
DOI: 10.35530/IT.077.05.2025128
Published online: October 2026

Abstract

Technological innovation efficiency is a pivotal metric for assessing a firm’s innovation capability, and equity structure is a key determinant shaping it. This study investigates this relationship within China’s listed textile sector (Shanghai and Shenzhen A-share markets, 2013–2024). To isolate the true managerial performance, we employ an integrated threestage Data Envelopment Analysis (DEA) model that purges the effects of external environmental factors and statistical noise. Subsequently, a Tobit regression is used to test the impacts of distinct equity governance mechanisms. The main findings are: (1) External environmental factors significantly inflate initial efficiency measurements; after purification, the overall decline is primarily driven by reduced pure technical efficiency, highlighting managerial practices as the critical bottleneck. (2) The adjustment reveals divergent paths: state-shareholding firms show improved efficiency mainly through scale efficiency, whereas non-state-shareholding firms exhibit a decline due to deficiencies in pure technical efficiency. (3) Regarding equity structure, ownership concentration, equity checks and balances, and institutional ownership all significantly promote technological innovation efficiency. In contrast, the mere presence of state shareholding exerts no statistically significant direct effect. These findings underscore that internal governance mechanisms, rather than ownership labels, are decisive for driving innovation efficiency in traditional manufacturing industries transforming.
Keywords: technological innovation efficiency, equity structure, corporate governance, textile industry, listed companies, three-stage DEA, Tobit model

Citation: Chen, G., Chen, H., He, S., The impact of equity structure on technological innovation efficiency in China’s listed textile firms, In: Industria Textila, 2026, 77, 5, 785–796,   https://doi.org/10.35530/IT.077.05.2025128

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Optimisation study of female suit product design based on the Kano-HOQ model

Authors: TONG WU, YING SONG
Pages 797–805 
DOI: 10.35530/IT.077.05.202580
Published online: October 2026

Abstract

This study adopts the Kano-HOQ method to address the gap between the consumption demands of female suit consumers and the market supply, improving the satisfaction of female suit consumers and the precision of market response. Firstly, 20 product demand factors influencing the consumption decisions of female suit consumers are extracted, classified and analysed according to Kano attributes. Then, based on the importance of each demand factor to the users, the comprehensive satisfaction of each consumption demand is calculated. The consumption demands of female suit consumers are transformed into 4 primary design requirements and 16 secondary design requirements. These are then input into the House of Quality (HOQ) model to determine the correlation between user demand factors and design requirements. Finally, by calculating the matrix, the weight values of each design requirement were determined, and they were ranked accordingly. The study summarised the consumer demand items and product design technical elements that should be prioritised for improvement in the female suit product design process. The research indicates that priority should be given to aesthetic appeal on the visual level in the design process of female suits, such as style, structure, colour, and patterns. At the same time, attention should also be paid to the personalised characteristics of the product, ensuring that it matches the individual demands of users. This approach aims to enhance user satisfaction and better fulfil consumer demands.
Keywords: female suit, user demands, Kano model, House of Quality, design requirement

Citation: Wu, T., Song, Y., Optimisation study of female suit product design based on the Kano-HOQ model, In: Industria Textila, 2026, 77, 5, 797–805,   https://doi.org/10.35530/IT.077.05.202580

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: The impact of the need for uniqueness on counterfeit luxury apparel consumption: an attitude-based mediation model

Author: ESRA OZTURK
Pages 806–814 
DOI: 10.35530/IT.077.05.2025161
Published online: October 2026

Abstract

Economic and technological developments in recent years have facilitated the introduction of counterfeit products into the market. The spread of counterfeit luxury apparel has brought on both legal and economic challenges for the global textile industry. This study examines the mediating role of attitude in the relationship between consumers’ need for uniqueness and their purchase intentions for counterfeit luxury apparel products in Türkiye, a country with a high circulation of counterfeit products. Data from 365 Turkish participants collected via an online survey were analysed using Structural Equation Modelling (SEM). The findings indicate that the NFU significantly increases positive attitudes toward counterfeit apparel, and these attitudes are a strong predictor of purchase intentions. The lack of a significant direct relationship between the NFU and purchase intentions suggests a full mediating effect of attitude. These findings explain why individuals purchase counterfeit luxury apparel and suggest an argument for promoting ethical and sustainable luxury products.
Keywords: need for uniqueness, counterfeit products, luxury apparel, consumer behaviour, textile industry, apparel

Citation: Öztürk, E., The impact of the need for uniqueness on counterfeit luxury apparel consumption: an attitude-based mediation model, In: Industria Textila, 2026, 77, 5, 806–814,   https://doi.org/10.35530/IT.077.05.2025161

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Design and characterisation of silica-reinforced nonwoven agricultural fabrics for plant protection and agricultural production

Authors: METEHAN ANAC, DEVRIM SOYASLAN DEMIRAY, MELIHA OKTAV BULUT
Pages 815–825 
DOI: 10.35530/IT.077.05.2025135
Published online: October 2026

Abstract

Agricultural textiles protect crops from detrimental weather and pests while promoting sustainable agriculture. This research introduces an innovative nonwoven polypropylene (PP) fabric directly incorporated with silicon dioxide (silica) to diminish pesticide application. Silica acts as a physical insecticide by disrupting pests’ protective wax coatings, offering an alternative to chemical pesticides that harm the environment and human health. UV-stabilized and non-stabilised polypropylene textiles were treated with silica at concentrations of 2%, 3%, and 5%. Essential qualities were evaluated, encompassing air permeability, tensile and tear strength, ageing resistance, and thermal stability (FTIR, DSC, TGA). SEM and EDS studies validated the presence and dispersion of silica. The findings indicated that silica diminished air permeability, thereby aiding in the retention of soil moisture and safeguarding plants. Although tensile and tear strength experienced minor reductions (up to 11% and 25%, respectively), the textiles continued to perform satisfactorily. Thermal investigations revealed slight alterations in decomposition temperatures. SEM–EDS showed that silica was evenly spread out but decreased a bit after ageing, suggesting that better fixing is needed for longer use. This direct incorporation of silica enhances pest control efficacy and UV resistance without dependence on chemical pesticides. The method promotes sustainable agriculture by improving crop protection and mitigating environmental hazards. Future research should concentrate on enhancing silica retention and conducting tests in actual field settings to create more robust agricultural textiles.
Keywords: agricultural textiles, silica, non-woven, fabric, UV ageing

Citation: Anaç, M., Demiray, D.S., Bulut, M.O., Design and characterisation of silica-reinforced nonwoven agricultural fabrics for plant protection and agricultural production, In: Industria Textila, 2026, 77, 5, 815–825,   https://doi.org/10.35530/IT.077.05.2025135

Full text PDF
Export citation and abstract       BibTeX     RIS

Article: Applying a linguistic MCDM method to handle the machinery purchase problem in the textile industry

Authors: CHEN CHEN-TUNG, OVA ALPER, HUNG WEI-ZHAN
Pages 826–833 
DOI: 10.35530/IT.077.05.2025172
Published online: October 2026

Abstract

Machinery investment decisions are complex, multi-criteria problems that require balancing cost, performance, and quality factors under uncertainty. This research introduces a linguistic multi-criteria decision-making (MCDM) method regarding machinery investments, integrating both qualitative and quantitative information in a structured computational framework. To ensure objectivity in the evaluation process, the entropy weighting method is employed to determine the criteria importance based on data dispersion. The proposed model enables experts’ linguistic judgments to be transformed into comparable numerical scales, allowing seamless integration with quantitative data in a single decision matrix. An empirical application to the laser cutting machine investment issue in the textile sector demonstrates the method’s effectiveness in ranking alternatives and reducing subjectivity in decision-making. Results show that the model provides transparent, reproducible, and computationally efficient evaluations. The study contributes to the broader industrial engineering literature by extending linguistic MCDM applications to machinery investment decisions, offering managers a systematic and data-driven tool for complex capital allocation problems.
Keywords: investment selection, linguistic MCDM, machinery selection, management, textile companies

Citation: Chen-Tung, C., Alper, O., Wei-Zhan, H., Applying a linguistic MCDM method to handle the machinery purchase problem in the textile industry, In: Industria Textila, 2026, 77, 5, 826–833,   https://doi.org/10.35530/IT.077.05.2025172

Full text PDF
Export citation and abstract       BibTeX     RIS

© Copyright 2026 INCDTP